Tools are required for this class. The tool list can be found HERE (Propane + NG Column). About the Class: Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment. ...
Oilheat Technician Training is a five-week course that offers extensive hands-on learning in our 2,400-square-foot oil lab.
MTEC's 12-week HVAC-R Professional program provides a comprehensive foundation for those entering the HVAC-R field.
This is a 4-day hands-on workshop focused on repairing gas and electric major appliances, as well as ventilation and gas distribution systems for small to medium-sized kitchen equipment.
Tank Setter & Outside Piping is a six-day course that covers the outside piping from the tank to the 2nd stage regulator.
Large Equipment Connection & Service is a two day, Board approved training course that prepares students specifically for the state Large Equipment exam.
Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment.
The Delivery Technician class is a four day course that prepares students specifically for the state Delivery Operator exam.
The Plant Operator class covers the codes and safety required to obtain a Plant Operator's license.
Introduction to A/C and Heat Pumps is designed for someone with zero experience with air conditioning and heat pumps.
Refrigerant Recovery and EPA 608 Certification is a five-day course covering refrigerant recovery and EPA Section 608 Certification (so you can handle and purchase refrigerants).
This two-day course will cover how to properly use an electrical multimeter and the proper rating of the tester and testing procedures. It will also cover how to read and interpret electrical components and ladder diagrams.
Mini Split Installer Training covers the installation and service of today’s high-efficiency heat pump systems.
608 EPA Certification is strongly recommended before taking this class. Tools required for this class can be found in the A/C/R Column HERE . About the Class: Mini Split Installer Training covers the ...
Tank Setter & Outside Piping is a six-day course that covers the outside piping, proper tank distances, bulk plants, and dispensing stations
Oilheat Technician Training is a five-week course that offers extensive hands-on learning in our 2,400-square-foot oil lab.
The Delivery Technician class is a four day course that prepares students specifically for the state Delivery Operator exam.
Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment. The class covers venting, electricity, and pipe sizing and offers hands-on training in MTEC's 1,400-square-foot state-of-the-art lab.
Explore the integration of electric heat pumps with gas or oil-fired furnaces for dual-fuel systems controlled by a single thermostat.
A one-day workshop tailored to meet the evolving rebate requirements for whole-home heat pump installations.
Large Equipment Connection & Service is a two day, Board approved training course that prepares students specifically for the state Large Equipment exam.
A2L Refrigerant Handling is a one-day course that covers the proper handling and recovery procedures for both A2L and hydrocarbon refrigerants. ...
The Heat Pump Service Procedures course will prepare technicians to perform service and maintenance of mini spilt heat pumps.
Tank Setter & Outside Piping is a six-day course that covers the outside piping, proper tank distances, bulk plants, and dispensing stations
Oilheat Technician Training is a five-week course that offers extensive hands-on learning in our 2,400-square-foot oil lab.
MTEC's 12-week HVAC-R Professional program provides a comprehensive foundation for those entering the HVAC-R field.
Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment. The class covers venting, electricity, and pipe sizing and offers hands-on training in MTEC's 1,400-square-foot state-of-the-art lab.
The Heat Pump Service Procedures course will prepare technicians to perform service and maintenance of mini spilt heat pumps.
Learn to install and service pumps, vaporizers, and liquid meters while mastering flaring burner setup and operation.
This 12-hour course equips students with the skills to effectively control hydronic heating systems using top brands.
A two-day course that provides in-depth training on piping strategies for non-condensing oil-fired boilers and gas-condensing boilers.
This one-day course empowers students to master manual heat loss calculations and system design for HVAC installations.
Learn how to properly size domestic hot water systems for both residential and commercial applications.
Refrigerant Recovery and EPA 608 Certification is a five-day course covering refrigerant recovery and EPA Section 608 Certification (so you can handle and purchase refrigerants).
Operator Qualification (OQ) training equips operators with the necessary skills and knowledge to comply with regulations and maintain safe propane system operations.
Mini Split Installer Training covers the installation and service of today’s high-efficiency heat pump systems.
Tank Setter & Outside Piping is a six-day course that covers the outside piping, proper tank distances, bulk plants, and dispensing stations
Oilheat Technician Training is a five-week course that offers extensive hands-on learning in our 2,400-square-foot oil lab.
Introduction to A/C and Heat Pumps is designed for someone with zero experience with air conditioning and heat pumps.
Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment. The class covers venting, electricity, and pipe sizing and offers hands-on training in MTEC's 1,400-square-foot state-of-the-art lab.
The Delivery Technician class is a four day course that prepares students specifically for the state Delivery Operator exam.
Tools are required for this class. The tool list can be found HERE (Oilheat Column). About the Class: Oilheat Technician Training - Night is a night course version of our five-week day course so you can train while you ...
Large Equipment Connection & Service is a two day, Board approved training course that prepares students specifically for the state Large Equipment exam.
Solid Fuel License Prep is a one-day code review test prep that will also review how to install Solid Fuel units with Liquid Fuels Units.
This 12-hour course equips students with the skills to effectively control hydronic heating systems using top brands.
A two-day course that provides in-depth training on piping strategies for non-condensing oil-fired boilers and gas-condensing boilers.
Refrigerant Recovery and EPA 608 Certification is a five-day course covering refrigerant recovery and EPA Section 608 Certification (so you can handle and purchase refrigerants).
This class has a required tool kit. A tool bag with all tools is part of your tuition price. The tools you'll be provided with can be found HERE (HVAC Pro Column). About the HVAC-R Professional Program: MTEC's 12-week ...
This is a 4-day hands-on workshop focused on repairing gas and electric major appliances, as well as ventilation and gas distribution systems for small to medium-sized kitchen equipment.
Mini Split Installer Training covers the installation and service of today’s high-efficiency heat pump systems.
About the Class: This class prepares the technician for both the Maine State Journeyman and Master's level exams. Please bring your NORA Silver Manual, NFPA 31 (2011) to class. About MTEC's Oilheat Technician Training Program: ...
Tank Setter & Outside Piping is a six-day course that covers the outside piping, proper tank distances, bulk plants, and dispensing stations
Explore the integration of electric heat pumps with gas or oil-fired furnaces for dual-fuel systems controlled by a single thermostat.
A one-day workshop tailored to meet the evolving rebate requirements for whole-home heat pump installations.
Introduction to A/C and Heat Pumps is designed for someone with zero experience with air conditioning and heat pumps.
Appliance Connection & Service is a four-week course where students will learn to install and service gas equipment. The class covers venting, electricity, and pipe sizing and offers hands-on training in MTEC's 1,400-square-foot state-of-the-art lab.
This class prepares the technician for the Maine State Propane and Natural Gas Exam: Appliance Connection and Service Technician.
608 EPA Certification and 40h Hour Heat Pump Training is strongly recommended before taking this class. Tools required for this class can be found in the A/C/R Column HERE . About the Class: The ...
Oilheat Technician Training is a five-week course that offers extensive hands-on learning in our 2,400-square-foot oil lab.
